No stress come to Point-S !!!
Brakes
Brakes are pretty much the most important safety device on your car. If you've even partially lost your brakes in the past, you'll remember the change of underwear that followed. Inspecting your brakes twice a year for wear and damage can protect you and your passengers while saving you money by catching any damage before it becomes too costly.
On many cars you can inspect the brakes without even removing the wheel. If your car has alloy wheels with spaces in the middle, you can get a proper assessment done by just peeping through the hole at the goodies. Whether you can peep through your wheel or you have to take the wheel off, be sure you have a clear view of the brake pads and the big shiny disc.
Let's inspect the disc first. It should be shiny from the inside to the outer edge, and fairly uniform. Don't worry if you can see slight lines in it, this is normal wear. However, if there are any rough spots or pronounced grooves in the disc, you should replace your brake discs. Brake discs should always be replaced in pairs so that your car's driveability and safety are not compromised.
Now take a look at the pads. You'll have to peek up to see them, but if you follow the surface of the disc to the top, you'll see the outside pad touching the disc. If there is 1/8" or less remaining on the pad, it's time for new ones. That's about the height of two pennies stacked. Don't worry, brake pads are cheap and replacing your brake pads is a no-sweat job.
Finally, take a look at your brake lines. Rubber coated lines should be soft and supple, not cracked and rigid. If you see cracks in flexible brake lines they will need to be replaced. Also be sure to inspect the hard, metal lines. These can become corroded, especially in snowy regions where chemicals are used on the roads.Brakefluid should be checked and maitained at service intervals..
DISC SKIMMING
Discs are usually damaged in one of four ways: scarring, cracking, warping or excessive rusting. Service shops will sometimes respond to any disc problem by changing out the discs entirely, This is done mainly where the cost of a new disc may actually be lower than the cost of labour to resurface the old disc.
Mechanically this is unnecessary unless the discs have reached manufacturer's minimum recommended thickness, which would make it unsafe to use them, or vane rusting is severe (ventilated discs only). Most leading vehicle manufacturers recommend brake disc skimming as a solution for lateral run-out, vibration issues and brake noises. The machining process is performed in a brake lathe, which removes a very thin layer off the disc surface to clean off minor damage and restore uniform thickness. Machining the disc as necessary will maximise the mileage out of the current discs on the vehicle.
Come to us for a free check on your brakes,and get a quotation on new ones !!!!
On many cars you can inspect the brakes without even removing the wheel. If your car has alloy wheels with spaces in the middle, you can get a proper assessment done by just peeping through the hole at the goodies. Whether you can peep through your wheel or you have to take the wheel off, be sure you have a clear view of the brake pads and the big shiny disc.
Let's inspect the disc first. It should be shiny from the inside to the outer edge, and fairly uniform. Don't worry if you can see slight lines in it, this is normal wear. However, if there are any rough spots or pronounced grooves in the disc, you should replace your brake discs. Brake discs should always be replaced in pairs so that your car's driveability and safety are not compromised.
Now take a look at the pads. You'll have to peek up to see them, but if you follow the surface of the disc to the top, you'll see the outside pad touching the disc. If there is 1/8" or less remaining on the pad, it's time for new ones. That's about the height of two pennies stacked. Don't worry, brake pads are cheap and replacing your brake pads is a no-sweat job.
Finally, take a look at your brake lines. Rubber coated lines should be soft and supple, not cracked and rigid. If you see cracks in flexible brake lines they will need to be replaced. Also be sure to inspect the hard, metal lines. These can become corroded, especially in snowy regions where chemicals are used on the roads.Brakefluid should be checked and maitained at service intervals..
DISC SKIMMING
Discs are usually damaged in one of four ways: scarring, cracking, warping or excessive rusting. Service shops will sometimes respond to any disc problem by changing out the discs entirely, This is done mainly where the cost of a new disc may actually be lower than the cost of labour to resurface the old disc.
Mechanically this is unnecessary unless the discs have reached manufacturer's minimum recommended thickness, which would make it unsafe to use them, or vane rusting is severe (ventilated discs only). Most leading vehicle manufacturers recommend brake disc skimming as a solution for lateral run-out, vibration issues and brake noises. The machining process is performed in a brake lathe, which removes a very thin layer off the disc surface to clean off minor damage and restore uniform thickness. Machining the disc as necessary will maximise the mileage out of the current discs on the vehicle.
Come to us for a free check on your brakes,and get a quotation on new ones !!!!